P613160
911 3,0 RSR 74
1974 -
Engine and fuel feed > Injection
1
11.92 kg
RSR slide valve injection system with 41, 43 and 46 mm diameter Complete slide valve injection system for the Porsche 911 RSR in the diameters 41, 43 and 46 mm. Slide valve injection systems have been used in Porsche racing vehicles since the 1960s in order to achieve maximum engine performance. The main advantage of a slide valve injection system is that when the slide valve is fully open, the maximum flow values can be achieved with the minimum opening cross-section. In contrast to a throttle valve system, neither a vertical flap nor a shaft nor screws, which on the one hand reduce the usable flow cross-section and on the other hand can introduce undesired turbulence into the gas column, interfere here. This in turn has the advantage of being able to achieve higher flow values despite the reduced cross-section, which can always be converted directly into power. Furthermore, the mass of the gas column is reduced by the smaller cross section, which enables an additional increase in performance due to the vibration behavior of the gas column. Flow measurements in our house have shown a flow value reduction of less than 1%. The intake funnels supplied in each case always have exactly the right cross-section and, thanks to the extremely high manufacturing quality, there are no disturbing edges or transitions in the assembled state. The only disadvantage that a slide valve injection system had for a long time could be completely eliminated through the complex construction and processing of this system. For a long time, this was the high "breakaway torque" from idling into the partial load range, which is a thing of the past with this system. When idling, the high negative pressure below the slide plates led to an increased need for force to open the slide, which suddenly decreases as soon as the negative pressure breaks down when the slide is opened. Our systems prevent this completely by guiding the slide plate in hardened industrial needle bearings, which are constructed with such high precision that the high-strength slide plates slide almost frictionlessly with no contact in the housing. The housing, on the other hand, was manufactured using the aluminum sand-casting process of that time, and was secured against warping and jamming despite the various temperature influences thanks to a complex heat treatment. In addition, the surfaces of the raceways of the needle roller bearings are resistant to wear in a further galvanic hardening process and therefore maintenance-free.
Other versions available for the part:
SHEAR VALVE 911 RSR ST TYPE 46 MM PAIR FOR ENGINE OVER 3.0 LITRES
GUILLOTINE TYPE INJECTION 3.0 RSR COMPLETE KIT
MAGNESIUM / 43 MM
The other parts in the family « Engine and fuel feed »
Oil filter console tube
ROHR OIL FILTER CONSOLE
Front oil cooler
FRONT OIL COOLER 911 3.0 RSR
Regulating thermostat for fitting on extra oil radiator
OIL COOLER THERMOSTAT
Kn air filter cleaner
Kn air filter cleaner
Servicing oil for kn air filter
Servicing oil for kn air filter
Guillotine type injection for 3.0 rsr, complete kit
GUILLOTINE TYPE INJECTION 3.0 RSR COMPLETE KIT
MAGNESIUM / 43 MM
SHEAR VALVE 911 RSR ST TYPE 46 MM PAIR FOR ENGINE OVER 3.0 LITRES
Timing casing cover
Cover for chain housing left r rsr
LEFT
Cover for chain housing left r rsr
RIGHT
Crankshaft pulley
Crankshaft pulley 911 look rsr
Conduite huile moteur RSR
RSR ENGINE OIL LINE
Flexible hose kit for 3.0 rsr type mechanical injection
FLEXIBLE HOSE KIT FOR 3.0 RSR TYPE MECHANICAL INJECTION
FLEXIBLE HOSE KIT FOR 3.0 RSR TYPE MECHANICAL INJECTION
Complete kit of gaskets for mechanical injection pump
COMPLETE GASKET KIT FOR MECHANICAL INJECTION PUMP 911 3.0 RSR
Blower turbine casing
FAN CASING 911 3.0RSR + 911ST + 906 + 914/6GT
225 MM
Sports engine cover kit
SPORT ENGINE COVER KIT 911 RSR LARGE TURBINE WITHOUT RADIATOR
Self-adhesive strip on engine
IGNITION POINT LABEL RSR
Plate for front oil radiator rsr
OIL COOLER DUCT FRONT OIL COOLER PANEL 911 3.0 RSR
Engine silent block (one)
ONE
Oil tank, 911 2.8 3.0 rsr
Oil tank, 911 2.8 3.0 rsr
Rsr camshaft nut
Rsr camshaft nut
Rsr rocker arm with pads
KIT OF 12 ROCKER ROCKER 911 RSR WITH PELLET ADJUSTMENT
Rsr rocker arm with pads
Bonnet type fuel filler kit
Fuel filler kit on bonnet 911 65-89 (for metal tank)
Fuel filler cap, rsr type
FUEL FILLER CAP, RSR TYPE