Bearing sleeve 8
Detailed list of the various versions
Select below the options you want to use to filter the list of parts concerned on the right-hand side of the screen.
Other
Bearing sleeve 8
INTERIOR MEASUREMENT STANDARD / EXTERIOR MEASUREMENT STANDARD
Bearing sleeve 8
INTERIOR MEASUREMENT -0.25 / EXTERIOR MEASUREMENT STANDARD
Bearing sleeve 8
INTERIOR MEASUREMENT -0.50 / EXTERIOR MEASUREMENT STANDARD
Bearing sleeve 8
INTERIOR MEASUREMENT STANDARD / EXTERIOR MEASUREMENT +0.25
Bearing sleeve 8
INTERIOR MEASUREMENT -0.25 / EXTERIOR MEASUREMENT +0.25
BEARING SLEEVE 8
INTERIOR MEASUREMENT STANDARD / EXTERIOR MEASUREMENT +0.50
BEARING SLEEVE 8
INTERIOR MEASUREMENT -0.50 / EXTERIOR MEASUREMENT +0.50
BEARING SLEEVE 8
COTE INTERIEUR -1MM / COTE EXTERIEUR +0.50
New part
4 Versions available for this part
MARK 3
3 Versions available for this part
8 Versions available for this part
3 Versions available for this part
3 Versions available for this part
3 Versions available for this part
9 Versions available for this part
In the same category:
INTERIOR MEASUREMENT STANDARD / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT -0.25 / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT -0.50 / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT STANDARD / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT -0.25 / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT -0.50 / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT -0.50 / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT STANDARD / EXTERIOR MEASUREMENT +0.25
INTERIOR MEASUREMENT -0.25 / EXTERIOR MEASUREMENT +0.25
INTERIOR MEASUREMENT STANDARD / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT -0.25 / EXTERIOR MEASUREMENT STANDARD
REPAIR MEASUREMENT -0.50 MM / SOLD PER UNIT
STANDARD MEASUREMENT / SOLD PER UNIT
REPAIR MEASUREMENT -0.25 MM / SOLD PER UNIT
REPAIR MEASUREMENT -0.50 MM / COMPLETE KIT
STANDARD MEASUREMENT / COMPLETE KIT
REPAIR MEASUREMENT -0.25 MM / COMPLETE KIT
INTERIOR MEASUREMENT -0.25 / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT -0.50 / EXTERIOR MEASUREMENT STANDARD
INTERIOR MEASUREMENT STANDARD / EXTERIOR MEASUREMENT STANDARD
New part
Oil gallery
UPPER
OIL COOLER THERMOSTAT
Kn sports air filter
Kn air filter cleaner
Servicing oil for kn air filter
Direct intake kit 996 turbo
Engine oil mobil1 0w40
1 LITRES
GULF OIL FORMULA G 5W40
1 LITRES
Engine oil mobil1 0w40
5 LITRES
GULF FORMULA G 5W40 OIL
5 LITRES
GULF FLAT OIL 4 - 6 5W50
4.5 LITRES
Fuel tank cap
PLASTIC
REVISION KIT 996 TURBO / GT2 2001 - 2005 WITH PARTICLE FILTER WITHOUT ACTIVATED CARBON
REVISION KIT 996 TURBO / GT2 2001 - 2005 WITH PARTICULATE FILTER WITH ACTIVATED CARBON
INTERMEDIATE SHAFT SPROCKET ALUMINUM COMPETITION VERSION
High strength forged connecting rods (full set)
CARRILLO MAKE / NON-REINFORCED CONNECTING ROD SCREWS FOR ENGINE SPEEDS NOT EXCEEDING 8,500 RPM
HIGH STRENGTH FORGED CONNECTING RODS (FULL SET)
CARRILLO MAKE / REINFORCED CONNECTING ROD SCREWS STANDING UP TO ENGINE SPEEDS OF OVER 8,500 RPM
GENERATION EV1/EV6 INJECTOR CONNECTION KIT
Preparation 996 box
VERY HIGH STRENGTH COMPETITION CYLINDER HEAD STUD KIT
Other diagrams in the family « Engine and fuel feed »
Engine and fuel feed
